Fix Solved: Moving A Raid Installed Operating System Tutorial=

Home > Solved Moving > Solved: Moving A Raid Installed Operating System

Solved: Moving A Raid Installed Operating System

Dad. I will try what you suggested and give feedback later.Thanks again!~Jim~ Jim951Dec 28, 2009, 9:51 AM Well, it worked ... If it doesn't work, or you can't repair the SSD to boot properly, you can always roll back to the array. The BIOS RAID process is more complex to turn on than Windows software RAID (driver needs to be installed & BIOS settings adjusted), and is hardware dependant. have a peek at this web-site

I'd much rather tell mdadm the correct version than have it guess it. OS: Win 10 Pro x64 CPU: Intel i7-4790K Motherboard: ASRock Z97 Extreme6 Memory: Corsair Vengeance Pro Series 16GB (2x8GB) 2400Mhz Graphics Card: ASUS ROG Strix GeForceŽ GTX 1070 Sound Card: Purity [email protected]:~# mdadm -V mdadm - v3.1.4 - 31st August 2010 [email protected]:~# mdadm --detail --scan ARRAY /dev/md0 metadata=0.90 UUID=d4e58776:640274d8:e368bf24:bd0fce41 I'm the wrong person to ask about why the version hasn't been updated. So that left me with 6 drives across 2 Intel SATA 3 ports, 4 Intel SATA 2 ports & 2 Marvel SATA 3 ports. http://www.tomshardware.com/forum/253961-32-move-raid-drive

Boot to BIOS, switch BIOS from AHCI to RAID. Windows doesn't do fakeraid. Hope that helps :) MakOwnerApril 10th, 2011, 03:44 AMSure, you can always get info to assemble the array from any of your disks that where part of the array (in the WempererJul 2, 2013, 2:30 AM Are you saying even if I have two drives in raid 1, if one drive fails, the other drive wont be accessible until I replace the

Do either of them allow you to move the drive to another computer? That's a compromise that's made for the stability that it offers. The problem at this point is you will need to 'break' the RAID (wiping both 2TB clean) and have to start over. I expected to be able to power the new server down, connect in the array, and with mdadm installed, power up and run mdadm --detail --scan as root and find the

rubylaserApril 11th, 2011, 01:20 AMI'ld love to find a good substitute that lives in the standard repos that will work both facing the internet and internally. All rights reserved Use of this Site constitutes acceptance of our User Agreement (effective 3/21/12) and Privacy Policy (effective 3/21/12), and Ars Technica Addendum (effective 5/17/2012) Your California Privacy Rights The I certainly never mentioned you should expect problems in the future. click for more info The only thing i can think of offhand would be if ordering makes a difference, which I don't think it does.

It should work for you with only minor changes. If one drive fails, you will run fine with just one drive.FYI, Windows RAID works this way too nicknomo wrote:You can even reverse the process by simply turning RAID off in Dad. solved Can I keep my OS if I move my hard drive to a new computer?

Here is what I do, using ghost (and usually a bartPE disk)...The hardest part usually is setting up your installation of Windows to boot once you go from non-RAID to RAID. I'm asking, because I don't have this same feeling. I'm not surprised that's not up to date in the repos. If there is only one tested copy, you are not backed up.

I started putting UUIDs in my /etc/fstab when I started messing with RAID/LVM. Check This Out Backed up again, post driver install. another good "drive imaging" program is Acronis True Imagebut I have no direct experience with it. Encryption causes the data to be (like RAID or NTFS) to be wrapped inside the code to be decrypted and encrypted to read / write operations.

Exactly how to do this varies with the chipset so if its not obvious let us know exactly which motherbd you have.Theres no need to reinstall as AHCI is a subset Win 7, Norton Ghost & Partition wizard recovery disks were on hand. Installation & Setup Converting to Raid 0 Windows 7, NOT Hardware Raid 0I have tried to find the way to do this, but without success as I cannot see the wood Source If you want something with cutting edge packages, run a Debian Sid or Arch.

Last edited by ghost333 (2013-05-23 09:23:38) Offline #2 2013-05-21 22:35:09 fukawi2 Forum Moderator From: .vic.au Registered: 2007-09-28 Posts: 5,342 Website Re: [SOLVED] Need to make RAID 1 to an already installed It has very minimal installation requirements, similar to most php web apps. They copy a source drive on to the second drive...

It is far easier to just buy an add on RAID card, and then boot to windows with that RAID card installed (but not yet in use).For the hardware / mirroring

If the problem has been known for that long, why no fix? If so, can you post the output of this command? Gamer. Motherboard: ASUS P9X79PRO, SATA Ports as follows: 2 x Intel SATA 3 4 x Intel SATA 2 2 x Marvel SATA 2 CPU i7 3820, 32GB OS Win 7 Professional x64

nicknomo Ars Tribunus Militum Registered: Mar 14, 2006Posts: 1696 Posted: Thu Oct 21, 2010 10:36 am elh wrote:The only reason I'd want to go to RAID-1 is to better protect the Most software raid chipsets use a different driver for single drive and RAID configurations, sometimes you can change the driver in the OS before ghosting, sometimes not.You can just install the My RAID disk was visible but still showing zero capacity so I formatted it again from diskmgr and then it was ready. have a peek here if the Raptor's C: partition is the ONLY partition on that HDD.

Rewriting over the top of the original OS is definitely possible, I've done it.